20 Things You Need To Be Educated About Repairs To Upvc Windows

Repairs to uPVC Windows

uPVC is a great choice for modern homes. They are long-lasting, durable and easy to maintain. They don't rot or rust like aluminum and timber.

It is essential to clean and oil UPVC doors and windows regularly. This will reduce costly repairs and improve energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause severe damage to your home and even be fatal. It is essential to take the time to ensure that you're doing all you can to ensure that your windows are in good repair.

For single pane windows it is fairly easy to replace windows, and the new one will usually fit inside the frame of the previous one easily. However If you have double-pane windows that are anchored by internal beading it will be more difficult to remove the existing panes and install new ones. In this instance you'll need to find some plastic spacers that will assist the new pane to fit perfectly into the frame of the window.

If you're planning to attempt to remove the window panes yourself, it is essential to wear appropriate safety gear that includes gloves with a thick layer of material and protective eyewear. It is also recommended to lay down a dropcloth before you start working on the glass so that any shards will fall onto the cloth rather than on the floor where they can be trodden under and cause further damage.

Once the glass has been removed, it's a good idea to seal the gap with clear packaging tape or duct tape to block water and drafts from getting into the property until a professional is able to come out and repair the window. It also acts as a barrier, preventing any intruders to gain access into your home. If the gap is large, you may be interested in the security door with an integrated window, as it will provide the best of both worlds.

2. Sagging

uPVC is a durable energy-efficient, cost-effective and economical alternative to timber sash window. In time, they could develop a number of problems, including sliding. A window that isn't properly aligned can cause problems with light, draughts or even security. If you find that your uPVC window is beginning to sag it is important to act swiftly to prevent the problem from getting worse.

To repair a window that is sagging, you can try to reposition the hinges. To accomplish this, you'll need to open the Window Repair so that you can access the frame. Then, you can remove the top and bottom hinges using a screwdriver and adjust them counter-clockwise or clockwise. Close your window to check the fit after you have repositioned your hinges. If you're happy with the fit, tighten the screws until they remain in position.

If you are unable to reposition the hinges, you might need to replace the seal. Over time rubber seals can lose their elasticity and dry out, which causes them to lose tightness. It is essential to replace your seal as soon as you can to ensure that your uPVC window watertight and draughtproof.

UPVC handles can also loosen. This is typically caused by screws that have loosened over time, but it can be due to the mechanism of the handle getting worn out. Fortunately, it's easy to fix the loose uPVC window handle yourself. First, you'll need to shut the window and do an experiment fitting. The joint at the corner of the sash must align with the joint on the casing. If it doesn't then you can use a screwdriver or a wrench to loosen the handle, and then turn the mechanism back into its original position.

3. Water Leaks

It is crucial to act if you awake each day to find mouldy walls and floors that are wet. Water leaks from windows are not just a cause for destruction of your home's structure but also hinder your efforts to regulate the temperature within your home. The most common reason for leaking uPVC windows is that the sealant around the frame is either damaged or missing.

This is a relatively easy fix that can be completed by any skilled DIYer. Based on the severity of the problem the old caulking might need to be removed before a new layer of caulk is applied. It is crucial to keep in mind that when it is about uPVC window repairs, do not be tempted to 'over-caulk' as this will only make the area more difficult to clean and can reduce your energy efficiency.

Verify that the drainage holes are free of debris inside them and that the sill pan has been properly angled to allow the water to drain from the window. In more serious situations, you might need to consider replacing the window.

Mold spots and rotten sills are also signs of water leakage. This fungus thrives under conditions of dampness and can spread quickly throughout the house.

If the leakage is occurring between the double-glazed glass it is more likely the problem is related to the seal, not the frame. This can be easily fixed by a uPVC window specialist who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be at fault if your upvc window repair window is difficult to open or if it opens in the breeze. They can be easily replaced by any competent DIYer and are usually completed in a matter of minutes.

Like any mechanical component, hinges can be damaged over time. The process of replacing a hinge on a window is essentially a simple procedure, but it is easier to do with someone else to assist in holding the frame up.

It is also worth checking that the uPVC hinges are opening and closed in the right direction. You can check this by checking for the arrows on each hinge. This shows which way the window should be opened.

Faulty window hinges could be caused by improperly opening the window a certain manner or because of inadequate installation at the factory. This can often be resolved by sending us a photo via our website and we will be happy to give you advice.

Regularly lubricating the hinges is essential. This can be done by applying an oil that is light in nature to the hinges. We suggest using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It can also lower the chance of windows getting stuck and stop corrosion. It is recommended to do this once a year. WD40 and other solvent based fluids are not recommended since they will damage parts of your uPVC window.

5. Draughts

Draughts can be caused by different factors. Firstly the hinges, again due to wear and tear may become displaced, which causes gaps to develop where the sash meets the frame. If they're beyond repair, it could be necessary to get them re-aligned. Second, the interlock can also become disaligned. It is located on the hinge's side, and could require to be cleaned. In some instances, it may be necessary to replace them.

The next most common reason for draughts are the window seals. They can become worn down or damaged over time, and allow air to escape through these gaps. This can be prevented by replacing them with high-quality weatherstripping. Another option is to replace the window with low-emissivity glass, this will help to regulate indoor temperatures and will reduce the possibility of draughts.

Another, and most effective methods to reduce the draughts in your home is to use an draught excluder. These are typically fabric tubes which are filled with a type of filler. They can be placed on the windowsill on top. They can help block out cold air and keep your home warm and cosy!

The windows made of upvc can continue to provide excellent insulation and security to your home with a little regular maintenance and repairs. It is crucial to keep in mind that all windows will eventually get worn out and it may be more cost-effective to simply replace them rather than repair them. If you are having issues with your upvc windows, it is best to seek professional assistance as soon as possible.